PS3Yes Release Free PSGRADE Downgrade Hex - Works on All AT90usb162 Boards

[pogg]

works like a charm on minimus avr usb v1

[KaMi SaMa]

@tuma

- Make SURE you got the correct files with correct names on your USB stick. Sometimes we find lv2diag.self renamed to lv2diag.self.1 or lv2diag.self.2 instead of having them in separate subdirectories in the archive.

- Remember that there is TWO different lv2diag.self files. One is used when downgrading to 3.41 (together with ps3updat.pup). The other is used by itself (no other files on the usb memory stick!) to EXIT the service mode.

- Remember to have the USB memory card in the RIGHTMOST slot and no other stuff in USB.

- Remove and replace power cable on slim / turn off then on switch on phat before starting the PS3 (maybe not neccessary but when you have problems make sure to try this!) in every step.

- WAIT! for the 3.41 install to finish. The PS3 will turn off (red led) when finished. Give it 30 minutes even if no lights are flashing, as long as the green led is on the firmware installation should be running.

[coltsfan4life-PSG]

Dang, still no P3go update -_-

[tuma]

@tuma

- Make SURE you got the correct files with correct names on your USB stick. Sometimes we find lv2diag.self renamed to lv2diag.self.1 or lv2diag.self.2 instead of having them in separate subdirectories in the archive.

- Remember that there is TWO different lv2diag.self files. One is used when downgrading to 3.41 (together with ps3updat.pup). The other is used by itself (no other files on the usb memory stick!) to EXIT the service mode.

- Remember to have the USB memory card in the RIGHTMOST slot and no other stuff in USB.

- Remove and replace power cable on slim / turn off then on switch on phat before starting the PS3 (maybe not neccessary but when you have problems make sure to try this!) in every step.

- WAIT! for the 3.41 install to finish. The PS3 will turn off (red led) when finished. Give it 30 minutes even if no lights are flashing, as long as the green led is on the firmware installation should be running.

But in order to get to that stage, one has to be factory mode. Mine won't go into factory mode. I have followed the steps outlined in order to flash the at90usb162 board and on the PC, it gives no indication of a problem. I plug it into the PS3 and follow the steps and the PS3 ignores it and boots normally.

[Galea-PSG]

But in order to get to that stage, one has to be factory mode. Mine won't go into factory mode. I have followed the steps outlined in order to flash the at90usb162 board and on the PC, it gives no indication of a problem. I plug it into the PS3 and follow the steps and the PS3 ignores it and boots normally.

I have same problem. Which file i need to use for AT90USB162? I tried all four hex files. I flashed i with Atmel Flip 3.4.2 verified ok. But no go on factory mode, normal boot. What should i do?

[farukdemirhan-PSG]

there are many hex files. Which hex file we'll download and update for AT90usb162?

[farukdemirhan-PSG]

Pls help to me about hex files?

[tuma]

there are many hex files. Which hex file we'll download and update for AT90usb162?

depends on the type you have. If yours has a 16Mhz clock than use the 16Mhz hex file, if not use the 8Mhz hex file.

[farukdemirhan-PSG]

depends on the type you have. If yours has a 16Mhz clock than use the 16Mhz hex file, if not use the 8Mhz hex file.

thanks for ur reply. my device is AT90usb162. i think it 8Mhz,right?

[tuma]

thanks for ur reply. my device is AT90usb162. i think it 8Mhz,right?

yeh..like mine. i couldn't get mine to work though. maybe you will have better luck.