PSGroove Ported to Rockbox for Sansa e200 series and others

[Pesebrero]

I dont know why but using manual install method by id10terror or DanyL's program now gives me an "Unknown USB device" on the PS3 and "Generic USB Hub" on Windows 7.

I tried uninstalling rockbox + bootloader (cbl) and reinstalling; plus every other combination. Rockbox USB is detected w/o the payload. Once I load the Payload, rockbox's USB detection goes down the crapper.

Any help? =]

Thanks!


*** Edit: This is happening to the Hermes V4B Payload which is why I am perplexed. As I know PL3 does this. ***

As far as I know, when using a payload, USB mass storage functionality is lost within Rockbox. This has happened to me since Hermes V1. You can use Sandisk original firmware to access the device through USB by pressing the <| key while turning on (if it's an E200).

[CrAzYNeSs]

As far as I know, when using a payload, USB mass storage functionality is lost within Rockbox. This has happened to me since Hermes V1. You can use Sandisk original firmware to access the device through USB by pressing the <| key while turning on (if it's an E200).

Thanks for the prompt reply Pesebrero! I would be okay with it if it were still injecting the payload. However, after the USB detection stopped in Rockbox (it was working before with the payload), so did the JB. I am at a lost right now.

[bitsbubba]

I dont know why but using manual install method by id10terror or DanyL's program now gives me an "Unknown USB device" on the PS3 and "Generic USB Hub" on Windows 7.

I tried uninstalling rockbox + bootloader (cbl) and reinstalling; plus every other combination. Rockbox USB is detected w/o the payload. Once I load the Payload, rockbox's USB detection goes down the crapper.

Any help? =]

Thanks!


*** Edit: This is happening to the Hermes V4B Payload which is why I am perplexed. As I know PL3 does this. ***

when JBing wait till status bar comes to the end ( on iPod) then hit 'power-eject' that should JB it. On PC you want to be in appleOS for in rockbox it acts as a USB dongle

[CrashSerious]

I dont know why but using manual install method by id10terror or DanyL's program now gives me an "Unknown USB device" on the PS3 and "Generic USB Hub" on Windows 7.

I tried uninstalling rockbox + bootloader (cbl) and reinstalling; plus every other combination. Rockbox USB is detected w/o the payload. Once I load the Payload, rockbox's USB detection goes down the crapper.

Any help? =]

Thanks!


*** Edit: This is happening to the Hermes V4B Payload which is why I am perplexed. As I know PL3 does this. ***

This has done this on my Sansa c200v1 from day one and it doesn't effect it one bit. In fact-- it's a sign that you have Rockbox-PSGroove installed properly pretty much because it ONLY happens with RB-PSGroove.

For everyone reading this (not nessisarily you CrAzYNeSs) if and your getting this popup on the PS3 and it *ISN'T* jailbroken it's a sign your doing something in the startup wrong or you have a compilation for your device for a different firmware.

[CoBrA2168]

Does anyone have an updated e200 code that spoofs the firmware?

[CrashSerious]

Does anyone have an updated e200 code that spoofs the firmware?

I have one for it with the PSN Patch for firmware 3.15. Haven't uploaded it because no one has offered to test it and report back the results so I can share it with everyone.

PM me if you'd like to be my e200 tester.

[CrAzYNeSs]

This has done this on my Sansa c200v1 from day one and it doesn't effect it one bit. In fact-- it's a sign that you have Rockbox-PSGroove installed properly pretty much because it ONLY happens with RB-PSGroove.

For everyone reading this (not nessisarily you CrAzYNeSs) if and your getting this popup on the PS3 and it *ISN'T* jailbroken it's a sign your doing something in the startup wrong or you have a compilation for your device for a different firmware.

Hello CrashSerious,

You were absolutely right. For some weird reason or other it was detected before. Now, even though it is NOT detected, it works perfectly fine. Thanks for the guidance.

For the C240, what I do now is Unplug Cord, Power On, Eject, immediately turn on C240, hold Select (my default key for Hermes v4b). It has worked flawlessly.

[CrashSerious]

Hello CrashSerious,

You were absolutely right. For some weird reason or other it was detected before. Now, even though it is NOT detected, it works perfectly fine. Thanks for the guidance.

For the C240, what I do now is Unplug Cord, Power On, Eject, immediately turn on C240, hold Select (my default key for Hermes v4b). It has worked flawlessly.

Glad you got it working. Wierd that you had to do that though, my c200v1 doesn't care one bit if it's been on all day-- it still jailbreaks the PS3.

[CoBrA2168]

I have one for it with the PSN Patch for firmware 3.15. Haven't uploaded it because no one has offered to test it and report back the results so I can share it with everyone.

PM me if you'd like to be my e200 tester.

Im on 3.41

[CrashSerious]

FYI. Anyone out there on FW 3.30, 2.76, 3.21, or 3.40?

PL3 has added support for these firmwares and I've modified Rockbo-PSGroove to support them as well. (3.30 was today.)