PIC18F2455 HEX files for Usb Spi Nand Reader

http://www.diygadget.com/media/catal...pi.600_1_1.jpg


Download hex files for this board (12mhz crystal)

(latest hex file contain is hermes_v1 confirmed working)
http://www.megaupload.com/?d=QPWS7F7B

hermes v3 payload thanks to iLLNESS

PSGrooPIC1.7a for 3.41 firmware only. compatible with PIC18F chips using the picdem bootloader or similar. LED outputs on RB1/RB4/RB5/RC0 so it should have LEDs working on most any board.

Features:
BD EMU, Hermes V3 Payload (Compatible with 3.41 firmware, No disk, Homebrew on usb, etc!). Basically everything hermesv3 supports.

PSGrooPIC_1.7a-3.41_18Fxxxx-LEDB145C0-BTLDR.zip

iLLNESS post
http://psx-scene.com/forums/showthre...392#post528392

Download PSGrooPIC_1.5_18F2455_12MHZ_NOLVPNOMCLR_B1_BTLDR
http://psx-scene.com/forums/attachme...1&d=1285204188

Quote:

---

Originally Posted by iLLNESS

PSGrooPIC_1.5_18F2455_12MHZ_NOLVPNOMCLR_B1_BTLDR

AKA.
1.5 source
PIC18F2455 and compatible chips
12mhz oscillator
NOLVP and NOMCLR (dont need the 10kohm resistors for pullup/pulldowns)
LED output on RB1
BOOTLOADER compatible.

From now on, I think im only going to post bootloader compatible hexes unless otherwise requested in the irc chat room in my signature. As MetalPhreak has stated before, there is way too many boards out there with different settings. I STRONGLY suggest people put a bootloader on their PIC. It makes life alot easier for everyone including yourself. This way if we feel like it we can post a hex for each board with each led setting rather then 50 different variations of each.

If you do not have a 12mhz oscillator, or need LVP or MCLR, you can still use this hex just hit CANCEL when loading in PDFUSB. it will ignore the config settings in these hexes and retain whatever settings are already flashed in the bootloader.

So please, make life easier for us and program your bootloader according to how you want. This way, we dont need to post hexes for every frequency required, etc.

This hex was posted by request.

---

just waiting on someone to compile Hermes v3

I'm also waiting for Hermes v3 on the same board, I need to figure out how to do this stuff myself

I was waiting for the Hermes v3 as well and you can use this one posted by illness. i tested it myself and it works on my usb spi nand reader from diygadgets. Please make sure you hit cancel to the bootloader setting option though otherwise you can brick your device.

http://psx-scene.com/forums/showpost...postcount=1645

anyone able to confirm this?

Didn't work right for me

Quote:

---

Originally Posted by AJW7989

I was waiting for the Hermes v3 as well and you can use this one posted by illness. i tested it myself and it works on my usb spi nand reader from diygadgets. Please make sure you hit cancel to the bootloader setting option though otherwise you can brick your device.

http://psx-scene.com/forums/showpost...postcount=1645

---

Quote:

---

Originally Posted by djsquare

Didn't work right for me

---

I just tested it and illness compile works fine for my PIC18F2455 HEX files for Usb Spi Nand Reader.

alright sweet, I'll give it another go

Thanks you, I can confirm it works just fine

please somebody compile Waninkoko Mods PSGroove Hermesv3 to pic18f2455