The above video goes away if you are a member and logged in, so log in now!
Originally Posted by DazSH
Originally Posted by mick711
Hi not sure have a look at my post theres apic there the 12mhz chip is on the other side with legs soldered through also aint flashed it yet but its supposed to have a bootloader
Originally Posted by iLLNESS
I bought a PIC board a while ago and have since upgraded it to Hermes v1 after the seller sent me the update (titled 'PSGrooPICV1.5_BTL_Firmware_Fixed.hex').
I requested a HEX for Hermes v3 but he doesn't have it, and he suggested I try to find a HEX for a pic18f4550 or 18f2550 - & also said that it needs to be compiled for the MCHPUSB bootloader.
Please could somebody help me?
there are tons of Micrcochip Bootlaoder compatible hex files. but whats more important is your board's configuration and crystal frequency, is it 8mhz, 12mhz, 16mhz or 20mhz?.
Originally Posted by djhazardous
Please while asking for a hex file do post crystal frequency as well.
if i have to upgrade my key, i've to use the hex with bootloader, right (i haven't got a programmer)?
Please can anybody help how to dump lv2 with PSGrooPic? (well, i'd like to experiment with fw2.52 ..) I tried to follow KaKaRoTo's guide, but the current PSGrooPic and PSfreedom source codes are too different, and the pic's one a bit too cryptic to me :/
Thanks in advance!
someone compile and upload PSGrooPIC1.7-Hermes-v3 for 4550 with 16mhz
with MCHPUSB bootloader no led.
Here you go.
Originally Posted by dmitlee
Also uploading hex files for 12MHZ and 20MHZ
updated 1.7a Hermes v3 and
PSgrooPIC - Folder Shared from Box.net - Free Online File Storage
If you can't find the firmware for your board, twitter me
Here we go with a new release, this time for PSGrooPIC v1.6, remember:
- PSGrooPIC v1.6 is based on Waninkoko/KaKaRoTo Payload
- PSGrooPIC v1.7 is based on Hermes V3 Payload
Change list on PSGrooPIC v1.6d release:
- Allow the installation of demo packages through the "Install package files" menu.
- Added patches to fix problems with pads and savegames (only for fw 3.41). Thanks to Hermes. Hermes V3 Payload integrated into Waninkoko Payload.
So, if you want latest novelties, install PSGrooPIC v1.6d!!
Donīt forget to buy me a beer if this blog was useful to you...! Thanks.
PSGrooPIC flashing/DIY guide, FAQ
sorry for late reply, thanks it works fine. LED dont work, but thats not importent.
Originally Posted by giorgoxxi
Thanks once again, have a goodday further.
hi to all
I have a PIC18F4550 I/P I've insert it on an ART2003 Programmer that I made on my own...
with LPT (setting on ECP) and USB to give more power.
I'm trying to install the bootloader..
When I open winpic and setting the art2003, and thesting hardware I have "Hardware test ok"
When I select: testing device, I have "Device -> UNKNOW"
Anyway I try to program it and I open the bootloader.hex
Make the setting with the oscillator that I will use, mcrle etc
And when I click on Program All I have this Error:
I've try to make that circuit two times...I don't know what to do...
ERROR -> Writing adress 0x000000
written: 0xEF97 read: 0xFFFF
If I click on Read Device, winpic read my divice correctly, but if I click on Verify All at 98% I have the error:
Can someone please help me?
Verifing adress 0x300000
verified: 0xCF3F read: 0xFFFF
really thanks in advance