Hex File Collection For Various Boards

[FarenHeit]

Im having the same exact problem but i need to make a .hex file for that stick:

CC1101-USB-Lite 868MHz (CUL)
http://busware.de/tiki-index.php?page=CUL

it has the ATMega32U4 processor in it,
and im tryin' hard to get this started im in ubuntu and installed that gcc-avr
and modified the MCU, BOARD, and F_CPU lines within the Makefile already
but i can't go further...



Nice for you, care to elaborate how you fixed this ?
because i was having the same problem apparently but for the ATMega32U4...

Thanks !


EDIT: Nevermind i found an .hex file that suited my need

You have a PM

[FarenHeit]

i'm confused, I need to flash the MAX AVR USB. (http://www.vgcrepairs.biz/zen_store/...roducts_id=466) says it's based on AT90USB (162 i believe). Which file am I supposed to use?

::EDIT::

I see above, to use AT90USB162 which is what I thought. Correct me if i'm wrong please!

http://www.eurasia.nu/modules.php?na..._PSGroove_v1.1

[RRoD420]

Thanks Farenheit, is that file patched for backup manager already?

[EmperorX]

does anyone have a hex file for this device
USB AVR-ISP Programmer
name:ATmega48
flash:4096

[nibelheim]

So the first page has so many files. If I want to install PSGroove for the first time, do I install v1.0 then v1.1 over it? Or do I install straight to v1.1? (I want BM, and using teensy++ 2.0)

[udip]

I have updated the source files to use the LEDs. It should blink LED1 red several times, then blink it green. When done, it should turn on LED2 (green or blue).

Most people have the udip1c board.

There are a few udip1a boards out there.

[Yngwiedis]

I have updated the source files to use the LEDs. It should blink LED1 red several times, then blink it green. When done, it should turn on LED2 (green or blue).

Most people have the udip1c board.

There are a few udip1a boards out there.

udip1a hex is working like psgroove but no LEDs working in my board.

udip1c hex is working like psgroove and blink red one LED when PS3 booting and then nothing.
Can you check it again please ?

Thank you very much.

[thx1138]

So the first page has so many files. If I want to install PSGroove for the first time, do I install v1.0 then v1.1 over it? Or do I install straight to v1.1? (I want BM, and using teensy++ 2.0)

install straight to v1.1 use the hex that your board needs teensy++ 2.0

at90usb1286
Teensy++ 2.0

use this one PSGroove_1.1_All_Patched_No_BM.zip

it has all of in it the one you want is called psgroove_1.1_teensy++_2.0.hex

which is in side the zip

thx1138eb

[udip]

udip1a hex is working like psgroove but no LEDs working in my board.

udip1c hex is working like psgroove and blink red one LED when PS3 booting and then nothing.
Can you check it again please ?

Thank you very much.

OK, try udip1b.hex. Unfortunately, there are two types of LEDs, Red/Green and Green/Red. Board 1b and 1c are reversed color.

My kid's PS3 is already on the newer version. So, I can't really test it out.

[Yngwiedis]

OK, try udip1b.hex. Unfortunately, there are two types of LEDs, Red/Green and Green/Red. Board 1b and 1c are reversed color.

My kid's PS3 is already on the newer version. So, I can't really test it out.

Better now but not perfect...

When booting a green LED flashing and after the boot the other LED is permanently red