CECHA01 + Infectus

My original Phat just died for a second time. So I got a slim and am going to fix the Phat and since it has already cost me so much money I figure I will hook a Infectus up to it for fun. have been watching this thread since it came about and want to contribute where I can. I found this at git-hacks if anyone needs:

ATNORFLASH:
NOR/NAND flashing code and schematics for Atmel based microprocessors and development boards

git://git-hacks.com/atnorflash/atnorflash.git

Quote:

---

Originally Posted by dj_skitzo

for those waiting on an update from danixleet, i have one, we started soldering all the wires up, we are up to about number 12 now and have a problem, one of the silver soldering points/test points have fallen off, and cant get a reading out of the multimeter unless we hold the silver thing in place, any one got any ideas on fixing it?

---

Might wanna hit up the irc chats mentioned earlier in the thread, defy will probably know more about it.

Quote:

---

Originally Posted by Raikalo

Might wanna hit up the irc chats mentioned earlier in the thread, defy will probably know more about it.

---

will check it out tomorrow, just did the last wire, besides the broken one, 8 hours later, time for bed haha

Quote:

---

Originally Posted by dj_skitzo

for those waiting on an update from danixleet, i have one, we started soldering all the wires up, we are up to about number 12 now and have a problem, one of the silver soldering points/test points have fallen off, and cant get a reading out of the multimeter unless we hold the silver thing in place, any one got any ideas on fixing it?

---

Use a small drill bit and with light hand pressure give it a few twists to expose the copper under the pad.

Quote:

---

Originally Posted by wizdumb

Use a small drill bit and with light hand pressure give it a few twists to expose the copper under the pad.

---

just the bit...not with a drill
sry what seems to be common sense to some can be new to others

Quote:

---

Originally Posted by dmcbudman

just the bit...not with a drill

---

This

http://www.leethacker.com/images/i2z...6z52gfanzq.jpg


So it looks kinda messy and were probably gonna redo it will the correct wire! Many thanks to dj_skitzo for doing the board solder, i will solder up the teensy++ and the 3.3v when we have them..


We will keep you's posted, and have already setup the irc as stated before, but havent jumped on yet as like dj_skitzo said took many hrs to complete that process..

Quote:

---

Originally Posted by dj_skitzo

for those waiting on an update from danixleet, i have one, we started soldering all the wires up, we are up to about number 12 now and have a problem, one of the silver soldering points/test points have fallen off, and cant get a reading out of the multimeter unless we hold the silver thing in place, any one got any ideas on fixing it?

---

yea like its been said, small drill bit or use a sharp scapel, craft knife to 'carefully' scrap the coating off the top of the trace to expose the copper

Quote:

---

Originally Posted by nevik

My original Phat just died for a second time. So I got a slim and am going to fix the Phat and since it has already cost me so much money I figure I will hook a Infectus up to it for fun. have been watching this thread since it came about and want to contribute where I can. I found this at git-hacks if anyone needs:

ATNORFLASH:
NOR/NAND flashing code and schematics for Atmel based microprocessors and development boards

git://git-hacks.com/atnorflash/atnorflash.git

---

^^ this is defyboys flasher code to written for the Teensy++

in the process of resoldering new wires, (thinner ones) :)

Quote:

---

Originally Posted by dj_skitzo

in the process of resoldering new wires, (thinner ones) :)

---

Use ide ribbon cable if you need to but its preferrable to use kynar wrap wire if possible (Its a tiny wire with a special heat resistant jacket that almost completely reduces the drawback of the coating when heated)