v3(Help)

hi all
ok i have this ps2 v3 gh-007
some *idiot* has tryed to bild an No Solder Modchip in it but the problem ist that the chip is not in but the picture starts to get bad in 10 min and in 15-20 min it looks like this

http://www.milkom.de/form/4.jpg
http://www.milkom.de/form/5.jpg
http://www.milkom.de/form/6.jpg
amy ideas?
can it be that the ps2 becomes too hot? when i press resert the picture is bad but when i turn it off and wait 30 minutes its ok for 10 min
can i fix it buy buing one of thouse usb fans?
or is it somthing else

p.s. sorry for my bad English :(

is the fan running?

Gaz

yes its running :)

Since the fault happends due to warm-up, the best approach is to buy yourself a can of Freeze spray. Most TV and video spare parts retailers stock this item.
Here's what you need to do once you have the spray:
Take the bottom cover off your PS2 and remove the metalwork. Your main board should now be exposed.
Place your PS2 vertically, but be careful, since the bottoms not on it, it won't stay vertical very well.
Now turn your PS2 on and boot a game.
Wait for the fault to appear.
Now using the freeze spray, spray a small section of the main board and see if this corrects the fault. If not, spray in another section. Keep doing this until you find a spot where freezing it corrects the picture. Now you have to narrow it down by component.
You should have a fine spray attachment given to you when you bought your freeze spray. This attachment allows just a very narrow amount of spray to be ejected. You need to use this to spray each component in the general area where its most effective.
If you do it right, you'll find the exact component thats causing your problem.
Since your symptoms show picture tearing, you might want to try around the area of the IC thats shown in the pic bellow, as this controls alot of your video info.
Please let me know how you get on.
Good luck!!!
Regards,
Relayer :D :D :D :D

hi 10x for the answere
i am going to buy that spray in an hour and test
the question ist ist Freeze spray the spray that is uset to make thinks clean and its full with oxigen or is it onother one?
is it compresst air?

i have Freeze spray -52C°
and i am testin it shout i sopray direct on the chip ?

nope i have used the Spray from both sides but no result :(
****** ***** *****
any ideas?

Just check very good for loose wires/solder ball/splashes and stuff.

It's a know fact that things grow and shrink when they're heating up and collling down. Maybe a wire just barely touched a spot, when the picture is good, but when affected by heat, it wont, or just make a littel bit.

Resolder wire points and check the ntsc bridge/rgb fix.
You may also check your av out. It's also affected by heat, so maybe it isn't you ps2 wich causes the trouble, maybe your video cable...............

{edit}

Some added content. Be shure to check your NTSC fix point. If i can clearly see on teh pictures you provided, the image is in black and white (not the pictures itzelf, since there is a blue ext-in sign on your tv).
The NTSC fix, as you probably know, solves the black/white screens.

Quote:

---

Originally posted by DJGAIT
{edit}

Some added content. Be shure to check your NTSC fix point. If i can clearly see on teh pictures you provided, the image is in black and white (not the pictures itzelf, since there is a blue ext-in sign on your tv).
The NTSC fix, as you probably know, solves the black/white screens.

---

hmm no there is coloure
and there are no wires at all no mod
and i have check all the cabels in the ps2 no problem there:(

ok and here is ti the best of all
the ps2 games give bad picture
but dvd films not they are 100% ok
idees?
i will test it with ps one games when i get one :)