Major DMS4 EZI issues

[N£TM£ÇH]

yeah and leaving screws out on the shielding was not intended by sony.. when the shielding pressed against the motherboard it adds ground...

[EnTiTy]

cant say i didnt see this coming because i did it was a bad idea to start with full stop too many connections, small pitch on the ic's dont mix either as mentioned id say 25% at best install it correctly without a problem the rest are dead or do damage to the clips making the mod un usable without cutting the wires and hard wiring it not good %'s infact just had a brain wave they should supply customers with wire inserts without the nasty clips for seasoned pro's oh that sounded dirty for some reason lol

[EnTiTy]

yeah and leaving screws out on the shielding was not intended by sony.. when the shielding pressed against the motherboard it adds ground...

im not even going to go there ok i will lol the ps2 has one ground plane when one screw is connected correctly so are the rest of the screw grounds even if not directly connected to the sheilding its basic electrics the main use of the so called sheilding is to hold heat pads in place to stop overheating and rf signals causing havock with the ic's during operation.

[N£TM£ÇH]

go play your xbox

[liknsmak]

that's sad...I was hoping this solderless kit would be a quality product...

[ShadowKnyght]

)))) hehehe - EnTiTy your not turning into a suporter of that little ownzer who left peoples screws out are you!!

For a shield plate to work effectively I say you would want at least 2 screws one on each side to ensure connection to the ground plane on both ends of the plate - makes for better EMC (less emissions and noise interference)

Also as ya mentioned - better pressure against heat trasnferring pads etc

Just think if they only covered one side of your microwave with shielding... and or left gaps - no more kiddies

[fasman]

I just read there lame disclamer,basicly if there lame chip doesnt work or it brakes your ps you are STUFFED.

I useto have respect for dms when they releast DM$3 but now,the are just a bounce of lamers wanting $$$$.

[EnTiTy]

)))) hehehe - EnTiTy your not turning into a suporter of that little ownzer who left peoples screws out are you!!

For a shield plate to work effectively I say you would want at least 2 screws one on each side to ensure connection to the ground plane on both ends of the plate - makes for better EMC (less emissions and noise interference)

Also as ya mentioned - better pressure against heat trasnferring pads etc

Just think if they only covered one side of your microwave with shielding... and or left gaps - no more kiddies

hm dont got a clue where you got that from il remember who my freinds are in future

i was being sarcastic in my last post so seen as i got torid remarks i should reply, a microwave is a different ball game :P its radiation via radio waves

if you want to get picky you should stop using mobile phones seen as you mentioned microwaves aka radiowaves oh and you can forget that sat tv they all do long term damage to the dna aka deoxyribonucleic acid structure in the human body just to use the generic name for dna :P im a qualified radio operator ham for short so know my shit on radio waves they all do damage no matter how small just they have better treatment for cancer these days

back on topic i couldnt give a toss about the ezi trash and its makers its a shit design full stop

and what a remark from netmech very original but you get that from kids
EnTiTy

[EnTiTy]

I just read there lame disclamer,basicly if there lame chip doesnt work or it brakes your ps you are STUFFED.

I useto have respect for dms when they releast DM$3 but now,the are just a bounce of lamers wanting $$$$.

they aint got a leg to stand on with that disclamer who's to say the clip was not faulty in the first place and that caused the damage to the ps2/two its upto them by law to prove you caused the damage and to prove it was not their device remember the customer is always right by law they are anyway until proven different

[fasman]

I dont know about the law in UK,but in South Africa the exact oppesite is also true.

You must prove that it was installed correctly.