Word around the scene is that there is a new fix for all of those looking to Remarry Blu Ray Drives to their CFW PS3 consoles. You can now Remarry from 3.55, without the need to downgrade your console; which was previously required in the process. This information comes from the PS3 Development Wiki, where you can find all the information that has been collected by various developers/sceners.
Remarry guide for 3.15 firmware
Click to View
1. Have the console on a working 3.15 firmware
2. Download the Remarry files (remarry-3.15.rar) and unpack to root of USM Mass Storage device. The following line is already changed from 1 to 0:
#---------------------------------------------
# Install Systemsoftware
# 0 = ���s���Ȃ�
# 1 = ���s����
#----------------------------------------------
0
This will make sure the drive init PUP is not installed, thus preventing RLOD because of syscon hashes on downgraded consoles.
3. Download official firmware <=3.30 as drive init PUP and put it root of USB Mass Storage device
Content of USB Mass Storage device should be thus be:
Lv2diag.self
manufacturing_updater_for_reset.self
fdm_spu_module.self
PS3UPDAT.PUP
cfg/standalone.cfg
4. Put the service mode JIG/dongle/PSGrade into port 0 (closest to the reader) and get into factory service mode.
5. Put the created USB Mass Storage device from step 3 into port 0 (closest to the reader) and run.
Drive Init Executing means it is starting the remarry process
Drive Init Failed with big pink letters 'NG' (No Good!) means the process failed. Most likely solved by fixing the communication issue with the drive.
6. After you run the initial remarry process, do not take it out of factory service mode.
7. Put a BD movie disc in and run it on the PS3. (This restores your DRL files!)
8. Then you can take it out of factory service mode.
9. Launch as normal.
2. Download the Remarry files (remarry-3.15.rar) and unpack to root of USM Mass Storage device. The following line is already changed from 1 to 0:
#---------------------------------------------
# Install Systemsoftware
# 0 = ���s���Ȃ�
# 1 = ���s����
#----------------------------------------------
0
This will make sure the drive init PUP is not installed, thus preventing RLOD because of syscon hashes on downgraded consoles.
3. Download official firmware <=3.30 as drive init PUP and put it root of USB Mass Storage device
Content of USB Mass Storage device should be thus be:
Lv2diag.self
manufacturing_updater_for_reset.self
fdm_spu_module.self
PS3UPDAT.PUP
cfg/standalone.cfg
4. Put the service mode JIG/dongle/PSGrade into port 0 (closest to the reader) and get into factory service mode.
5. Put the created USB Mass Storage device from step 3 into port 0 (closest to the reader) and run.
Drive Init Executing means it is starting the remarry process
Drive Init Failed with big pink letters 'NG' (No Good!) means the process failed. Most likely solved by fixing the communication issue with the drive.
6. After you run the initial remarry process, do not take it out of factory service mode.
7. Put a BD movie disc in and run it on the PS3. (This restores your DRL files!)
8. Then you can take it out of factory service mode.
9. Launch as normal.
Remarry guide for 3.50 firmware
Click to View!
1. Have the console on a working 3.50 firmware
2. Download the Remarry files (remarry-3.50.rar) and unpack to root of USM Mass Storage device. The following line is already changed from 1 to 0:
#---------------------------------------------
# Install Systemsoftware
# 0 = ���s���Ȃ�
# 1 = ���s����
#----------------------------------------------
0
This will make sure the drive init PUP is not installed, thus preventing RLOD because of syscon hashes on downgraded consoles.
3. Download official firmware <=3.30 as drive init PUP and put it root of USB Mass Storage device
Content of USB Mass Storage device should be thus be:
Lv2diag.self
manufacturing_updater_for_reset.self
fdm_spu_module.self
PS3UPDAT.PUP
cfg/standalone.cfg
4. Put the service mode JIG/dongle/PSGrade into port 0 (closest to the reader) and get into factory service mode.
5. Put the created USB Mass Storage device from step 3 into port 0 (closest to the reader) and run.
Drive Init Executing means it is starting the remarry process
Drive Init Failed with big pink letters 'NG' (No Good!) means the process failed. Most likely solved by fixing the communication issue with the drive.
6. After you run the initial remarry process, do not take it out of factory service mode.
7. Put a BD movie disc in and run it on the PS3. (This restores your DRL files!)
8. Then you can take it out of factory service mode.
9. Launch as normal.
2. Download the Remarry files (remarry-3.50.rar) and unpack to root of USM Mass Storage device. The following line is already changed from 1 to 0:
#---------------------------------------------
# Install Systemsoftware
# 0 = ���s���Ȃ�
# 1 = ���s����
#----------------------------------------------
0
This will make sure the drive init PUP is not installed, thus preventing RLOD because of syscon hashes on downgraded consoles.
3. Download official firmware <=3.30 as drive init PUP and put it root of USB Mass Storage device
Content of USB Mass Storage device should be thus be:
Lv2diag.self
manufacturing_updater_for_reset.self
fdm_spu_module.self
PS3UPDAT.PUP
cfg/standalone.cfg
4. Put the service mode JIG/dongle/PSGrade into port 0 (closest to the reader) and get into factory service mode.
5. Put the created USB Mass Storage device from step 3 into port 0 (closest to the reader) and run.
Drive Init Executing means it is starting the remarry process
Drive Init Failed with big pink letters 'NG' (No Good!) means the process failed. Most likely solved by fixing the communication issue with the drive.
6. After you run the initial remarry process, do not take it out of factory service mode.
7. Put a BD movie disc in and run it on the PS3. (This restores your DRL files!)
8. Then you can take it out of factory service mode.
9. Launch as normal.
Remarry Guide for 3.55 Firmware:
Click to View!
1. Have the console on a working 3.55 firmware
2. Download the Remarry files (remarry-3.55.rar) and unpack to root of USM Mass Storage device. The following line is already changed from 1 to 0:
#---------------------------------------------
# Install Systemsoftware
# 0 = ���s���Ȃ�
# 1 = ���s����
#----------------------------------------------
0
This will make sure the drive init PUP is not installed, thus preventing RLOD because of syscon hashes on downgraded consoles.
3. Download official firmware <=3.30 as drive init PUP and put it root of USB Mass Storage device
Content of USB Mass Storage device should be thus be:
Lv2diag.self
manufacturing_updater_for_reset.self
fdm_spu_module.self
PS3UPDAT.PUP
cfg/standalone.cfg
4. Put the service mode JIG/dongle/PSGrade into port 0 (closest to the reader) and get into factory service mode.
5. Put the created USB Mass Storage device from step 3 into port 0 (closest to the reader) and run.
Drive Init Executing means it is starting the remarry process
Drive Init Failed with big pink letters 'NG' (No Good!) means the process failed. Most likely solved by fixing the communication issue with the drive.
6. After you run the initial remarry process, do not take it out of factory service mode.
7. Put a BD movie disc in and run it on the PS3. (This restores your DRL files!)
8. Then you can take it out of factory service mode.
9. Launch as normal.
2. Download the Remarry files (remarry-3.55.rar) and unpack to root of USM Mass Storage device. The following line is already changed from 1 to 0:
#---------------------------------------------
# Install Systemsoftware
# 0 = ���s���Ȃ�
# 1 = ���s����
#----------------------------------------------
0
This will make sure the drive init PUP is not installed, thus preventing RLOD because of syscon hashes on downgraded consoles.
3. Download official firmware <=3.30 as drive init PUP and put it root of USB Mass Storage device
Content of USB Mass Storage device should be thus be:
Lv2diag.self
manufacturing_updater_for_reset.self
fdm_spu_module.self
PS3UPDAT.PUP
cfg/standalone.cfg
4. Put the service mode JIG/dongle/PSGrade into port 0 (closest to the reader) and get into factory service mode.
5. Put the created USB Mass Storage device from step 3 into port 0 (closest to the reader) and run.
Drive Init Executing means it is starting the remarry process
Drive Init Failed with big pink letters 'NG' (No Good!) means the process failed. Most likely solved by fixing the communication issue with the drive.
6. After you run the initial remarry process, do not take it out of factory service mode.
7. Put a BD movie disc in and run it on the PS3. (This restores your DRL files!)
8. Then you can take it out of factory service mode.
9. Launch as normal.
Download Links:
Source: Remarry
via: PS3 Dev Wiki
Daily Digest
Recent Threads
Recent Comments
vBulletin Message