Today we have some exciting news, for readers that own a kiosk/store/demo PS3 units. A member, by the name of starcube, has sent us a tutorial that will convert your demo PS3, into a fully functional retail unit. The tutorial utilizes service mode, so make sure you have a dongle capable of getting you into this mode (PSGrade etc).
Requirements: You will need the typical DGF (downgrade files) and a USB board with PSGrade loaded, as well as a standard USB stick.
First, we need to be able to use the jig and to do so, we need the kiosk to not auto start when switch is flipped. You can use the public PSGrade (the only version out there, there is no special kiosk version)
First do the following:
Have a disc in the drive
Turn off the power switch
Turn it back on until you see the Blu-Ray light flash one or two times
Turn it off at the power switch (in the back)
Turn it on again at the power switch (in the back)
Now, when you turn the power switch on, the PS3 will still be in standby mode, so we can act as if we are going to jailbreak the unit. Instead of a PSGroove hex, we're going to use our dongle with the PSGrade hex. Go about the normal procedure for jailbreaking, by pressing eject and power. The console will panic and shut down the first time. When you turn it back on your controller should desync and the resolution will be super low.
The vsh (XMB) for kiosk does not have the red box. However, if you see the console is in low res and controller is not syncing until plugged in, then the unit is in factory mode. Now unplug the JIG and power down the console normally.
Format a thumb drive to fat32 and make sure only lv2diag.self from the lv2diag 1 folder and ps3updat.pup are in the root of the thumb drive. Plug thumb drive into the usb port that is all the way to the right (if the console was laying down horizontally). Now, just push the power button to turn on your PS3.
You are going to see a black screen and your memory card light is gonna flicker for roughly 10 minutes until the process is done. The console will shut down on its own when it finishes, so don't mess with it until it's done.
When the console finishes doing its thing, turn it back on and it will be in red box (service) mode. Now, unplug the thumb drive and delete the 2 files you put in there. Then, put the lv2diag.self from lv2diag 2 folder and then plug it back into the same USB port, that it was in before. Once its plugged in, reboot the console. It will now finalize the install and turn it into a full blown retail. enjoy =)
-starcube
Requirements: You will need the typical DGF (downgrade files) and a USB board with PSGrade loaded, as well as a standard USB stick.
First, we need to be able to use the jig and to do so, we need the kiosk to not auto start when switch is flipped. You can use the public PSGrade (the only version out there, there is no special kiosk version)
First do the following:
Have a disc in the drive
Turn off the power switch
Turn it back on until you see the Blu-Ray light flash one or two times
Turn it off at the power switch (in the back)
Turn it on again at the power switch (in the back)
Now, when you turn the power switch on, the PS3 will still be in standby mode, so we can act as if we are going to jailbreak the unit. Instead of a PSGroove hex, we're going to use our dongle with the PSGrade hex. Go about the normal procedure for jailbreaking, by pressing eject and power. The console will panic and shut down the first time. When you turn it back on your controller should desync and the resolution will be super low.
The vsh (XMB) for kiosk does not have the red box. However, if you see the console is in low res and controller is not syncing until plugged in, then the unit is in factory mode. Now unplug the JIG and power down the console normally.
Format a thumb drive to fat32 and make sure only lv2diag.self from the lv2diag 1 folder and ps3updat.pup are in the root of the thumb drive. Plug thumb drive into the usb port that is all the way to the right (if the console was laying down horizontally). Now, just push the power button to turn on your PS3.
You are going to see a black screen and your memory card light is gonna flicker for roughly 10 minutes until the process is done. The console will shut down on its own when it finishes, so don't mess with it until it's done.
When the console finishes doing its thing, turn it back on and it will be in red box (service) mode. Now, unplug the thumb drive and delete the 2 files you put in there. Then, put the lv2diag.self from lv2diag 2 folder and then plug it back into the same USB port, that it was in before. Once its plugged in, reboot the console. It will now finalize the install and turn it into a full blown retail. enjoy =)
-starcube
Daily Digest
Recent Threads
Recent Comments
vBulletin Message